Recent Posts

Pages: [1] 2
1
E-TEC / Tilt trim NMEA 2000
« Last post by admin on May 13, 2018, 06:51:50 PM »
If you are trying to read your engines tilt and trim level via a NMEA 2K device then you must have the following.

1- EVDIAGS software to calibrate the range of the sensor.
2- a 47 ohn 5w(Minimum) resistor connected from the purple wire to the Wht/Tan wire on the analog gauge.

The analog gauge should be removed.

WARNING, do not apply 12V direct to the Wht/Tan wire this may damage the ECU.
2
E-TEC / Tilt trim indicator not working - TIP
« Last post by admin on May 13, 2018, 06:48:59 PM »
The tilt trim sensor has a loaded spring that can get gummed up overtime. lift the motor all the way up. The sensor is on the port side. carefully move the sensor arm up and down and make sure it has free motion. If it does not, remove the two bolts holding it in place. Spray some CRC silicone and continue to work it back and forth until the spring starts snapping it back into palce. Used some compressed air to clean any debri stuck in the part.

Hope this helps someone.
3
Suzuki Outboards / What information does Suzuki pass on the NMEA bus
« Last post by admin on April 01, 2018, 07:33:37 AM »
Lowrance has a nice doc showing the info passed onto the NMEA bus from a Suzuki motor:

https://ww2.lowrance.com/Global/Lowrance/Documents/NMEA/Suzuki%20Engine%20NMEA2000%20Connection.pdf
4
For Sale by Dealers / North Star Energy AGM 2100 12V Group 31 Battery
« Last post by admin on April 01, 2018, 07:01:35 AM »
North Star Energy AGM 2100 12V Group 31

Little over a year old

$250 Each
5
For Sale by Dealers / Twin 2004 Yamaha 200HP with rigging 2 Stroke HPDI
« Last post by admin on April 01, 2018, 07:00:43 AM »
Twin 2004 Yamaha 200HP with rigging 2 Stroke HPDI

Around 800 Hrs each motor

$7500 OBO

305.785.3355
6
Boat Maintenance and Repair / TIP: How to loosen 5200 to remove those stubborn parts
« Last post by admin on April 01, 2018, 06:57:15 AM »
Had to remove some hatches the other day and let me tell you someone went 3M 5200 CRAZY. They make some agent that will work but it's very expensive. So I tried a trick I learned a while back to remove Windows COA stickers from computers. Heat! It's important that you only apply enough heat as to not damage the surface. I use a variable heat gun from Home Depot Wagner Furno 750 Heat Gun. The surface was powder coated aluminum. I wasn't to concerned about damaging the powder coated since the hatches where getting resurfaced. 750-800 degrees (definitely want to use less heat for plastic or other non-metallic surfaces) for a couple of seconds was all I needed to loosen the glue and pry a corner off. I worked my way around and got them off fairly easily.

Hope this helps you DIYers
7
For Sale by Dealers / APCN Marine Mods Now sells AMSOIL
« Last post by admin on February 09, 2017, 07:14:32 PM »
APCN is now your one stop shop for all AMSOIL Products. Next generation Diesel Oil, Marine Two Cycle oil that exceeds most Engine Manufacturers specs, Gear Oil and more... Visit the AMSOIL site to learn more about their products and whats right for your engine. Call us today 786.618.1011
8
For Sale by Dealers / New warehouse in Miami!!
« Last post by admin on January 09, 2017, 09:31:25 PM »
We have a new location in Miami..

7215 NW 79 TER
MIAMI, FL 33166

786.618.1011
9
For Sale by Dealers / Our eBay Store - apriceforyou
« Last post by aplusmiami on February 21, 2016, 08:10:24 PM »
Visit our eBay store for deals on new and used equipment.

http://www.ebay.com/sch/apriceforyou/m.html
Pages: [1] 2